Saturday, August 18, 2018

Z-Flex Chimney Liners and Chimney Liner Systems


Global Pro Tankless Supply is now carrying Z-Flex Chimney Venting. Z-Flex Chimney Lining Systems can require a diverse range of parts, including but not limited to rigid and flexible venting, aluminum and stainless steel venting, and much more. 

Aluminum Chimney Liner Kits for Category I Gas Fired Heating Equipment and Gas Fireplaces

The Aluminum 2-Ply Chimney Liner Kit (2GACKIT__ __) is an aluminum chimney liner kit that includes a 2-ply aluminum liner according to the ordered length and diameter, chimney flashing, rain cap, mortar collar, and 3 screws.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"
Available in lengths from 20' to 50' in 5' increments.


The Additional Length of Aluminum 2-Ply Liner (2GAXXXX__ __) is a length of the same 2-ply liner included in the full kit (2GACKIT__ __). This is useful if additional venting is found to be needed in the installation process.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"
Available in lengths from 20' to 50' in 5' increments.

 
The Aluminum 2-Ply Extension Kit (2GAEXT__ __) is a kit that includes one 10 foot length of aluminum 2-ply liner, one coupling, and two clamps. This kit is especially useful if more than just an additional length of aluminum liner is needed.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


The Aluminum Liner Connector (2CNNTRG__) is a connector that attaches two lengths of aluminum liner together. This part may be needed if ordering additional lengths.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


Direct Vent Co-Linear Flexible Liner Kits

The DVI Kit (2DVI_35_) is a kit designed for use when converting any existing wood-burning fireplace into a gas-fired one. Allows for a completely sealed system that does not compromise indoor air quality. Kit includes 2 Triplelock Gas Liners (one for flue exhaust and another for outside combustion), and either an extreme weather or decorative co-linear termination option.
Available in the following diameters:  3" and 4”



Aluminum Chimney Liner Kits for Category I Gas Fired Heating Equipment and Gas Fireplaces

The 1-Ply Aluminum Duct (1TLXXXX__ __) is a duct that helps with the flow of fresh air in your chimney venting system. Please note that this product is not to be used as a chimney liner.
Available in the following diameters: 2”, 3", 4", 5", and  6"
Available in lengths from 20' to 50' in 5' increments.


The Fresh Air Hood (2FAIGAL__) is a hood that helps cycle in fresh air with your chimney venting system. The hood design keeps objects from entering.
Available in the following diameters: 2”, 3", and 4"


The B-Vent Connector (2CNNBFC__) is a connector that is used to attach type-b gas vents to Z-Flex aluminum chimney liners. Note that the B-Vent Connectors do not fit Hart & Cooley or Amerivent B-Vent
Available in the following diameters: 3", 4", 5", 6", 7", 8", and 10"


The Galvanized Y (2GAYXXX___) is a gas liner/adaptor that is used to connect two vent connectors to one common vent.
Available in the following diameters: 4” x 4” x 3”, 5” x 5” x 3”, 5” x 5” x 4”, 6” x 6” x 3”, 6” x 6” x 4”, 7” x 7” x 3”, 7” x 7” x 4”, and 8” x 8” x 4”.



Single Vent - Single Wall Flexible Vent Connectors

The Gas Single Vent Kit (2SVKXXX__ __) is a single wall flexible vent connector. Single-Vent, like Insul-Vent, is designed to make difficult installations easy and economical. It replaces rigid single pipe as a vent connector.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Single-Vent Universal Connector (2SVUCXX__) is a connector/adaptor used to connect Single-Vent to any type of single wall pipe. Examples include B-vent and Z-Flex chimney liner. 
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Single-Vent Appliance Connector (2ZSCPRP__) is a connector/adaptor used to connect Single-Vent to appliance collars. 
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Insul-Liner pre-insulated Chimney Liner for Category I Heating Equipment & Gas Fireplaces

The Insul-Liner Kit (2GIAKXX__ __) is an insulated liner kit best used in exterior chimneys or when a brick chimney has no clay liner. The National Fuel Gas Code recommends, but does not require that in certain situations liners be insulated.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Additional Length of Insul-Liner (2INSGAC__ __) is an additional liner length in case what came with the kit was not enough.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Insul-Vent Universal Connector (2IVUCXX__) is used to join Insul-Vent to any type of Single Wall pipe, type-b vent, or Z-Flex chimney liner.  
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Insul-Vent Double Wall Insulated Vent Connector Kits

The Gas Insul-Vent Double Wall Insulated Vent Connector Kit (2ZIKXXX__ __) is a single wall flexible insulated vent connector designed to make connections between appliance and common vent, such as L-Vent, masonry chimney, or Z-Flex Chimney liner products easy and economical.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Universal B-Vent “Y” (2IVTYUC04) is a y-vent that connects Insul-Vent to any existing B-vent.
Available in a 5” x 5” x 4” diameter


The Insul-Vent Appliance Connector (2ZICPRP__) is a connector/adaptor used to connect Insul-Vent to appliance collars. 
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Insul-Vent 3” to 4” Increaser (2ZIC314) is used to connect 3” appliances to 4” Insul-Vent.
Available in a 4” diameter


Single Wall Flexible Oil Vent Connectors

The Single Wall Oil Vent Connector Kit (2OVSKIT__ __) is a single wall flexible insulated vent connector designed to make connections between appliance and common vent, such as L-Vent, masonry chimney, or Z-Flex Chimney liner products easy and economical.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Additional Length of Single Wall Oil Vent Pipe (2ZLSSXX__ __) is an additional length of oil vent in case what came with the kit was not enough.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Single Wall Oil Vent Universal Connector (2OVSWUC__) is used to join single wall oil venting to any type of Single Wall pipe, type-L vent, or Z-Flex chimney liner. 
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Single Wall Oil Vent Appliance Connector (2OVSWAC__) is used to join single wall oil venting to appliance collars.
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Double Wall Flexible Oil Vent Connector

The Double Wall Oil Vent Connector Kit (2OVIKIT__ __) is a double wall flexible insulated vent connector designed to make connections between appliance and common vent, such as L-Vent, masonry chimney, or Z-Flex Chimney liner products easy and economical.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Additional Length of Double Wall Oil Vent Pipe (2OILVNT__ __) is a double wall flexible insulated vent length to be used with listed double wall oil vent connectors.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Double Wall Oil Vent Universal Connector (2OVIUCX__) is used to join double wall oil venting to any type of Double Wall pipe, type-L vent, or Z-Flex chimney liner. 
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Double Wall Oil Vent Appliance Connector (2OVIACX__) is used to join double wall oil venting to appliance collars.
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Stainless Steel Chimney Liner Kits for Oil, Gas & Pellet Stoves

The All Fuel Insert Kit (2OILKTX__ __I) is a chimney liner kit for use with Category I natural-draft gas-fired heating equipment and gas fireplaces. Includes a stainless steel liner, rain cap, chimney flashing, and a “dripless” connector.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Smoothcore Kit (2ZFSCKIT__ __) is a UL listed stainless steel chimney liner kit for use with Category I natural-draft gas-fired heating equipment and gas fireplaces. Smoothcore eliminates the turbulence inherent with corrugated liners, improving draft. Resists corrosive attack by not impeding the flow of condensate down the liner, with therefore, less opportunity for soot to accumulate.
Available in the following diameters: 3", 4", 5", 6", 7", 8"


The Triple-Lock Smoothcore All Fuels Chimney Liner (2ZLSCXX__ __) is a UL listed length of aluminum 2-ply chimney liner for use with Category I natural-draft gas-fired heating equipment and gas fireplaces.
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Oval All Fuel Stainless Steel

The Flexible Stainless Steel Oval to Round Liner (2ZLSSOR__ __) is a liner that transitions from oval to round venting. To be used in areas that is restrictive in one dimension.
Available in the following diameters: 6", 7", 8", and 10”


The Flexible Stainless Steel Full Oval Liner (2ZLSSOX__ __) is a liner that is oval all the way throughout for better navigation through tight spaces. To be used in areas that is restrictive in one dimension.
Available in the following diameters: 6", 7", 8", and 10”


The Stainless Steel Oval Base Tee with round take off (2ZRBIOX__) is a tee used to connect round venting to oval venting.
Available in the following diameters: 6", 7", 8", and 10”


The Stainless Steel Oval Liner Coupling (2CNNTRA__) is used to mate two pieces of oval liner together.
Available in the following diameters: 6", 7", 8", and 10”


The Stainless Steel Oval to Round Adapter (2ZRORAX__) is a connector/adaptor that is used to transition from oval to round venting. Round end accepts Z-Flex venting.
Available in the following diameters: 6", 7", 8", and 10”


The Stainless Steel Round to Oval Adapter (2ZRROAX__) is a connector/adaptor that is used to transition from round to oval venting. Oval end accepts Z-Flex venting.
Available in the following diameters: 6", 7", 8", and 10”



Z-VENT Stainless Steel Smoothcore Category II, III, IV Chimney Liner

The Smoothcore Gas Vent Length (2SVSCKIT__ __) is a UL listed Continuous length flexible Triple Lock Special Gas Vent for use with Category II III IV Gas and Propane fired heating appliances.
Available in the following diameters:  5", 6", 7", 8"



Stainless Steel AL 29-4C® Flexible Chimney Liner for Category 1 Gas Fired Equipment

The Stainless Steel Flexible Chimney Liner Kit (2KT294C__ __) is a UL listed stainless steel chimney liner kit for use with Category I natural-draft gas-fired heating equipment and gas fireplaces. Includes a liner, bird proof rain cap, stainless steel flashing, mortar collar, and top support.
Available in the following diameters: 3", 4", 5", 6", 7", 8"



Stainless Steel All Fuel Chimney Liner Kits

The All Fuel Stainless Steel Kit (2ZFLKIT__) comes complete with everything you need to quickly and easily install a professional venting system. It Includes a liner, Z-Max cap and flashing, and a Lock ‘N Go Tee.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


The Insulating Blanket with Wrap and Gear Clamps (2INSKIT__ __) is mandatory for wood burning applications. Three wrap and gear clamps included with every 5 ft. ordered.
Available in the following diameters:  4", 5", 6", 7", 8", and 10"



Stainless Steel Z-Max - Oil, Gas, Pellet Chimney Liner Kits

The Z-Max Oil, Gas, & Pellet Kit (2OILKTX__ __) is a UL listed stainless steel chimney liner kit for use with oil, gas, and pellet stoves. This kit comes with a stainless steel liner and a Z-Max cap + flashing.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10" (Note, this product is different than the 2OILKITX__ __I).


The Stainless Steel Self-Drilling Screws (2SSSCREW) is a bag of 50 screws for your venting needs.


The 2" Flex Ready Pellet Tee w/ 3" Branch (2ZPT43) is a tee that connects Z-Flex to solid fuel inserts where space is minimal.


The 2" Fresh Air Kit for Pellet Stoves (2FAKIT0205) is a kit that is meant to assist in air circulation for pellet stoves. This kit comes with a 2” x 5’ Aluminum 1-ply duct, 2” intake hood with screen, and two (2) 2” gear clamps.


Flexible Stainless Steel Round Liner Category I Chimney Liner

The Length of SS Alloy - AL 29-4C (2ZL294C__ __) is a UL listed length of SS Alloy AL 29-4C Liner ideal for use with gas, oil, pellets, and wood. Liner must be insulated with a Z-Flex Insulation blanket wood burning installation.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


The Smoothcore All Fuels Chimney Liner (2ZLSCXX__ __) is a UL listed length of aluminum 2-ply chimney liner for use with Category I natural-draft gas-fired heating equipment and gas fireplaces.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"



Stainless Steel Flexible Round Liner Category I Chimney Liners

The Stainless Steel Deluxe Rain Cap (2RNCAPS__) is a rain cap that prevents deterioration caused by moisture entering the chimney.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


The Stainless Steel Chimney Flashing (2ZSCSXX__) is used to seal off the top of the chimney after the installation is complete.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


The Z-Max Cap (2ZMRCS__) is a cap to be used in conjunction with the Z-Max Flashing (2AFCS__).
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8”


The Stainless Steel Drip-less Connector (2CNNTRC__) is a gas chimney liner connector that is used to attach Z-Flex Stainless Steel flexible liner to insert, Rigid Stacking Tee or Elbow. Designed to keep creosote/condensate within the liner space.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"



The Lock'N Go Tee (2ZFTCB__) is a style tee that installs in half the time compared to regular tees with no special tools required. Refer to rigid tee for use with rigid liner or when stacking tees together.
Available in the following diameters: 3", 4", 5", 6", 7", 8", 9", and 10"


The Z-Lok Tee (2ZFTJ__) is a style tee for secure connections in restricted work spaces. Z-Lok Tee body is specifically manufactured with a low profile mount that allows insertion right into tight chimney spaces.
Available in the following diameters: 3", 4", 5", 6", 7", 8", 9", and 10"



All Fuel Stainless Steel

The 304 Stainless Steel Rigid Liner (2ZR321F__ __) is a UL listed length of rigid liner with a fusion welded pipe seam for a smoother finish and a better fit.
Available in the following diameters:  5", 6", 7", 8", 9", and 10"


The Fixed Stainless Steel 45 Degree Elbow (2RE45XX__) is a rigid single-wall stainless steel elbow.
Available in the following diameters:  5", 6", 7", 8", 9", and 10"


The Fixed Stainless Steel 90 Degree Elbow (2RE90XX__) is a rigid single-wall stainless steel elbow.
Available in the following diameters:  5", 6", 7", 8", 9", and 10"



All Fuel Stainless Steel

The Stainless Steel Rigid Stacking Tee w/ Cap (2ZRBTXX__) is a style tee to be used with Z-Flex rigid liner or when stacking two tees together. Refer to flex ready tee for use with Z-Flexible liner.
Available in the following diameters: 3", 4", 5", 6", 7", 8", 9", and 10"


The Stainless Steel Increaser (2IN_I_X) is used to increase the liner size to accommodate a range of flue sizes, appliances, and installations.
Available in the following diameters: 4", 5", 6", 7", 8", and 10”


The Stainless Steel Reducer (2RD_R_X) is used to decrease the liner size to accommodate a range of flue sizes, appliances, and installations.
Available in the following diameters: 2”, 3", 4", 5", 6", 7", and 8"


The Stainless Steel Top Support (2ZTSXXX__) prevents rain or snow from entering the chimney. Top support clamps to Z-Flex liner to support the venting system and also holds the rain cap in place.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"


Nose Cone Tools

The Nose Cone (2NCXXX__) is used to snake flexible chimney liner down chimney flue. Tapered design self-centers liner for smoother installation.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"



Chimney Liner Finder - Gas & Oil

The Liner Sizing Charts (2CHART__) are charts used to size up chimney venting with what is needed.



Stainless Steel Aerocowls

The Stainless Steel Aerocowl (2ARCOWL__) is an aerodynamically designed unit, when fitted to structurally sound chimneys and flues, completely eliminates downdraft and thereby prevents troublesome smoke and toxic fumes which otherwise linger in the home.
Available in 12” and 18” diameters.


The Stainless Steel Aerocowl Round Base (2ARCORB__) is used to snake rigid chimney liner down chimney flue. Tapered design self-centers liner for smoother installation.
Available in the following diameters:  5", 6", 7", 8", and 10"


The Stainless Steel Aerocowl Universal Base (2ARCOUB) is used to snake rigid chimney liner down chimney flue. Tapered design self-centers liner for smoother installation. This base can fit with all the diameters the normal base can fit.



Thursday, August 2, 2018

Stiebel Eltron Tempra B & Tempra PLUS Electric Tankless Water Heaters

Global Protankless Supply is now carrying the full line of Stiebel Eltron electric tankless water heaters.  The Stiebel Eltron Tempra B & Tempra Plus models are a whole house electric tankless water heater.  These units provide endless hot water and are great for saving space. 

The Stiebel Eltron Tempra B units can be used with 240V/220V or 208V and come in a variety of different KW units ranging from 12KW up to 36KW for all types of applications.  These units are 99% efficient.  The Stiebel Eltron Tempra B units can accept inlet water temperatures up to 131 degrees F.  The Tempra B models have a temperature control on the front of the unit allowing the temperature to be adjusted from 86 - 140 degrees F.  Please remember anything over 125 degrees F is scalding.  A thermal cut-out switch provides an excellent safety measure and ensures that the heating elements will not need replacement, as they do with many other electric tankless water heaters. This small unit can be installed virtually anywhere in the home and, of course, produce an endless supply of hot water.  Below are links for the Stiebel Eltron Tempra B units:

Stiebel Eltron Tempra B Models:
Tempra 36 B
Tempra 29 B
Tempra 24 B
Tempra 20 B
Tempra 15 B
Tempra 12 B

The Stiebel Eltron Tempra PLUS units can be used with 240V/220V or 208V and come in a variety of different KW units ranging from 12KW up to 36KW for all types of applications.  These units are 99% efficient.  The Stiebel Eltron Tempra PLUS units can accept inlet water temperatures up to 131 degrees F.  The Tempra PLUS models have a temperature control on the front of the unit allowing the temperature to be adjusted from 86 - 140 degrees F.  The Tempra PLUS units also have a digital display that shows the temperature of the water when the unit is in use.  Stiebel Eltron Tempra Plus units come with Advanced Flow Control so if the unit senses too high a flow it will reduce the water flow to maintain a more consistent temperature.  Please remember anything over 125 degrees F is scalding.  A thermal cut-out switch provides an excellent safety measure and ensures that the heating elements will not need replacement, as they do with many other electric tankless water heaters. This small unit can be installed virtually anywhere in the home and, of course, produce an endless supply of hot water.  Below are links for the Stiebel Eltron Tempra PLUS units:

Stiebel Eltron Tempra PLUS Models:
Tempra 36 PLUS
Tempra 29 PLUS
Tempra 24 PLUS
Tempra 20 PLUS
Tempra 15 PLUS
Tempra 12 PLUS

For further questions or to place an order please call Global Protankless Supply at 866-289-4652