Global Pro Tankless Supply is now carrying Z-Flex
Chimney Venting. Z-Flex Chimney Lining Systems can require a diverse range of parts,
including but not limited to rigid and flexible venting, aluminum and stainless
steel venting, and much more.
Aluminum Chimney Liner Kits for Category I Gas Fired Heating Equipment and Gas Fireplaces
The Aluminum
2-Ply Chimney Liner Kit (2GACKIT__ __) is an aluminum chimney liner kit that
includes a 2-ply aluminum liner according to the ordered length and diameter,
chimney flashing, rain cap, mortar collar, and 3 screws.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Available in
lengths from 20' to 50' in 5' increments.
The
Additional Length of Aluminum 2-Ply Liner (2GAXXXX__ __) is a length of the
same 2-ply liner included in the full kit (2GACKIT__ __). This is useful if
additional venting is found to be needed in the installation process.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Available in
lengths from 20' to 50' in 5' increments.
The Aluminum 2-Ply Extension Kit (2GAEXT__ __) is a kit that includes one 10 foot length of aluminum 2-ply liner, one coupling, and two clamps. This kit is especially useful if more than just an additional length of aluminum liner is needed.
Available in the following diameters: 3", 4", 5" 5.5", 6", 7", 8", 9", and 10"
The Aluminum
Liner Connector (2CNNTRG__) is a connector that attaches two lengths of
aluminum liner together. This part may be needed if ordering additional
lengths.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Direct Vent Co-Linear Flexible Liner Kits
The DVI Kit (2DVI_35_) is a kit designed for use when converting any existing wood-burning fireplace into a gas-fired one. Allows for a completely sealed system that does not compromise indoor air quality. Kit includes 2 Triplelock Gas Liners (one for flue exhaust and another for outside combustion), and either an extreme weather or decorative co-linear termination option.
Available in the following diameters: 3" and 4”
Aluminum Chimney Liner Kits for Category I Gas Fired Heating Equipment and Gas Fireplaces
The 1-Ply
Aluminum Duct (1TLXXXX__ __) is a duct that helps with the flow of fresh air in
your chimney venting system. Please note that this product is not to be used as
a chimney liner.
Available in
the following diameters: 2”, 3", 4", 5", and 6"
Available in
lengths from 20' to 50' in 5' increments.
The Fresh
Air Hood (2FAIGAL__) is a hood that helps cycle in fresh air with your chimney
venting system. The hood design keeps objects from entering.
Available in
the following diameters: 2”, 3", and 4"
The B-Vent
Connector (2CNNBFC__) is a connector that is used to attach type-b gas vents to
Z-Flex aluminum chimney liners. Note that the B-Vent Connectors do not fit Hart
& Cooley or Amerivent B-Vent
Available in
the following diameters: 3", 4", 5", 6", 7", 8",
and 10"
The
Galvanized Y (2GAYXXX___) is a gas liner/adaptor that is used to connect two
vent connectors to one common vent.
Available in
the following diameters: 4” x 4” x 3”, 5” x 5” x 3”, 5” x 5” x 4”, 6” x 6” x
3”, 6” x 6” x 4”, 7” x 7” x 3”, 7” x 7” x 4”, and 8” x 8” x 4”.
Single Vent - Single Wall Flexible Vent Connectors
The Gas
Single Vent Kit (2SVKXXX__ __) is a single wall flexible vent connector.
Single-Vent, like Insul-Vent, is designed to make difficult installations easy
and economical. It replaces rigid single pipe as a vent connector.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Single-Vent Universal Connector (2SVUCXX__) is a connector/adaptor used to
connect Single-Vent to any type of single wall pipe. Examples include B-vent
and Z-Flex chimney liner.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Single-Vent Appliance Connector (2ZSCPRP__) is a connector/adaptor used to
connect Single-Vent to appliance collars.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Insul-Liner pre-insulated Chimney Liner for Category I Heating Equipment & Gas Fireplaces
Insul-Liner pre-insulated Chimney Liner for Category I Heating Equipment & Gas Fireplaces
The
Insul-Liner Kit (2GIAKXX__ __) is an insulated liner kit best used in exterior
chimneys or when a brick chimney has no clay liner. The National Fuel Gas Code
recommends, but does not require that in certain situations liners be
insulated.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Additional Length of Insul-Liner (2INSGAC__ __) is an additional liner length
in case what came with the kit was not enough.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Insul-Vent Universal Connector (2IVUCXX__) is used to join Insul-Vent to any
type of Single Wall pipe, type-b vent, or Z-Flex chimney liner.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Insul-Vent Double Wall Insulated Vent Connector Kits
The Gas
Insul-Vent Double Wall Insulated Vent Connector Kit (2ZIKXXX__ __) is a single
wall flexible insulated vent connector designed to make connections between
appliance and common vent, such as L-Vent, masonry chimney, or Z-Flex Chimney
liner products easy and economical.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Universal B-Vent “Y” (2IVTYUC04) is a y-vent that connects Insul-Vent to any
existing B-vent.
Available in
a 5” x 5” x 4” diameter
The
Insul-Vent Appliance Connector (2ZICPRP__) is a connector/adaptor used to
connect Insul-Vent to appliance collars.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Insul-Vent 3” to 4” Increaser (2ZIC314) is used to connect 3” appliances to 4”
Insul-Vent.
Available in
a 4” diameter
Single Wall Flexible Oil Vent Connectors
The Single
Wall Oil Vent Connector Kit (2OVSKIT__ __) is a single wall flexible insulated
vent connector designed to make connections between appliance and common vent,
such as L-Vent, masonry chimney, or Z-Flex Chimney liner products easy and
economical.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Additional Length of Single Wall Oil Vent Pipe (2ZLSSXX__ __) is an additional
length of oil vent in case what came with the kit was not enough.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The Single
Wall Oil Vent Universal Connector (2OVSWUC__) is used to join single wall oil
venting to any type of Single Wall pipe, type-L vent, or Z-Flex chimney
liner.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The Single
Wall Oil Vent Appliance Connector (2OVSWAC__) is used to join single wall oil
venting to appliance collars.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Double Wall Flexible Oil Vent Connector
The Double
Wall Oil Vent Connector Kit (2OVIKIT__ __) is a double wall flexible insulated
vent connector designed to make connections between appliance and common vent,
such as L-Vent, masonry chimney, or Z-Flex Chimney liner products easy and
economical.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Additional Length of Double Wall Oil Vent Pipe (2OILVNT__ __) is a double wall
flexible insulated vent length to be used with listed double wall oil vent
connectors.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The Double
Wall Oil Vent Universal Connector (2OVIUCX__) is used to join double wall oil
venting to any type of Double Wall pipe, type-L vent, or Z-Flex chimney
liner.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The Double
Wall Oil Vent Appliance Connector (2OVIACX__) is used to join double wall oil
venting to appliance collars.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Stainless Steel Chimney Liner Kits for Oil, Gas & Pellet Stoves
The All Fuel
Insert Kit (2OILKTX__ __I) is a chimney liner kit for use with Category I
natural-draft gas-fired heating equipment and gas fireplaces. Includes a
stainless steel liner, rain cap, chimney flashing, and a “dripless” connector.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Smoothcore Kit (2ZFSCKIT__ __) is a UL listed stainless steel chimney liner kit
for use with Category I natural-draft gas-fired heating equipment and gas
fireplaces. Smoothcore eliminates the turbulence inherent with corrugated
liners, improving draft. Resists corrosive attack by not impeding the flow of
condensate down the liner, with therefore, less opportunity for soot to
accumulate.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
The
Triple-Lock Smoothcore All Fuels Chimney Liner (2ZLSCXX__ __) is a UL listed
length of aluminum 2-ply chimney liner for use with Category I natural-draft
gas-fired heating equipment and gas fireplaces.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Oval All Fuel Stainless Steel
The Flexible
Stainless Steel Oval to Round Liner (2ZLSSOR__ __) is a liner that transitions
from oval to round venting. To be used in areas that is restrictive in one
dimension.
Available in
the following diameters: 6", 7", 8", and 10”
The Flexible
Stainless Steel Full Oval Liner (2ZLSSOX__ __) is a liner that is oval all
the way throughout for better navigation through tight spaces. To be used in
areas that is restrictive in one dimension.
Available in
the following diameters: 6", 7", 8", and 10”
The
Stainless Steel Oval Base Tee with round take off (2ZRBIOX__) is a tee
used to connect round venting to oval venting.
Available in
the following diameters: 6", 7", 8", and 10”
The
Stainless Steel Oval Liner Coupling (2CNNTRA__) is used to mate two pieces of
oval liner together.
Available in
the following diameters: 6", 7", 8", and 10”
The
Stainless Steel Oval to Round Adapter (2ZRORAX__) is a connector/adaptor that
is used to transition from oval to round venting. Round end accepts Z-Flex
venting.
Available in
the following diameters: 6", 7", 8", and 10”
The
Stainless Steel Round to Oval Adapter (2ZRROAX__) is a connector/adaptor that
is used to transition from round to oval venting. Oval end accepts Z-Flex
venting.
Available in
the following diameters: 6", 7", 8", and 10”
Z-VENT Stainless Steel Smoothcore Category II, III, IV Chimney Liner
The Smoothcore Gas Vent Length (2SVSCKIT__
__) is a UL listed Continuous length flexible Triple Lock Special Gas Vent for
use with Category II III IV Gas and Propane fired heating appliances.
Available in
the following diameters: 5",
6", 7", 8"
Stainless Steel AL 29-4C® Flexible Chimney Liner for Category 1 Gas Fired Equipment
The Stainless
Steel Flexible Chimney Liner Kit (2KT294C__ __) is a UL listed stainless steel
chimney liner kit for use with Category I natural-draft gas-fired heating
equipment and gas fireplaces. Includes a liner, bird proof rain cap, stainless
steel flashing, mortar collar, and top support.
Available in
the following diameters: 3", 4", 5", 6", 7", 8"
Stainless Steel All Fuel Chimney Liner Kits
The All Fuel
Stainless Steel Kit (2ZFLKIT__) comes complete with everything you need to
quickly and easily install a professional venting system. It Includes a liner,
Z-Max cap and flashing, and a Lock ‘N Go Tee.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
The Insulating
Blanket with Wrap and Gear Clamps (2INSKIT__ __) is mandatory for wood burning
applications. Three wrap and gear clamps included with every 5 ft. ordered.
Available in
the following diameters: 4",
5", 6", 7", 8", and 10"
Stainless Steel Z-Max - Oil, Gas, Pellet Chimney Liner Kits
The Z-Max
Oil, Gas, & Pellet Kit (2OILKTX__ __) is a UL listed stainless steel
chimney liner kit for use with oil, gas, and pellet stoves. This kit comes with
a stainless steel liner and a Z-Max cap + flashing.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10" (Note, this product is different than the
2OILKITX__ __I).
The
Stainless Steel Self-Drilling Screws (2SSSCREW) is a bag of 50 screws for your
venting needs.
The 2"
Flex Ready Pellet Tee w/ 3" Branch (2ZPT43) is a tee that connects Z-Flex
to solid fuel inserts where space is minimal.
The 2" Fresh
Air Kit for Pellet Stoves (2FAKIT0205) is a kit that is meant to assist in air
circulation for pellet stoves. This kit comes with a 2” x 5’ Aluminum 1-ply
duct, 2” intake hood with screen, and two (2) 2” gear clamps.
Flexible Stainless Steel Round Liner Category I Chimney Liner
The Length
of SS Alloy - AL 29-4C (2ZL294C__ __) is a UL listed length of SS Alloy AL
29-4C Liner ideal for use with gas, oil, pellets, and wood. Liner must be
insulated with a Z-Flex Insulation blanket wood burning installation.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
The Smoothcore
All Fuels Chimney Liner (2ZLSCXX__ __) is a UL listed length of aluminum 2-ply
chimney liner for use with Category I natural-draft gas-fired heating equipment
and gas fireplaces.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Stainless Steel Flexible Round Liner Category I Chimney Liners
The Stainless
Steel Deluxe Rain Cap (2RNCAPS__) is a rain cap that prevents deterioration
caused by moisture entering the chimney.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
The Stainless
Steel Chimney Flashing (2ZSCSXX__) is used to seal off the top of the chimney
after the installation is complete.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
The Z-Max
Cap (2ZMRCS__) is a cap to be used in conjunction with the Z-Max Flashing
(2AFCS__).
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8”
The Stainless
Steel Drip-less Connector (2CNNTRC__) is a gas chimney liner connector that is
used to attach Z-Flex Stainless Steel flexible liner to insert, Rigid Stacking
Tee or Elbow. Designed to keep creosote/condensate within the liner space.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
The Lock'N
Go Tee (2ZFTCB__) is a style tee that installs in half the time compared to
regular tees with no special tools required. Refer to rigid tee for use with
rigid liner or when stacking tees together.
Available in
the following diameters: 3", 4", 5", 6", 7", 8",
9", and 10"
The Z-Lok
Tee (2ZFTJ__) is a style tee for secure connections in restricted work spaces.
Z-Lok Tee body is specifically manufactured with a low profile mount that
allows insertion right into tight chimney spaces.
Available in
the following diameters: 3", 4", 5", 6", 7", 8",
9", and 10"
All Fuel Stainless Steel
The 304
Stainless Steel Rigid Liner (2ZR321F__ __) is a UL listed length of rigid liner
with a fusion welded pipe seam for a smoother finish and a better fit.
Available in
the following diameters: 5",
6", 7", 8", 9", and 10"
The Fixed
Stainless Steel 45 Degree Elbow (2RE45XX__) is a rigid single-wall stainless
steel elbow.
Available in
the following diameters: 5",
6", 7", 8", 9", and 10"
The Fixed
Stainless Steel 90 Degree Elbow (2RE90XX__) is a rigid single-wall stainless
steel elbow.
Available in
the following diameters: 5",
6", 7", 8", 9", and 10"
All Fuel Stainless Steel
The Stainless
Steel Rigid Stacking Tee w/ Cap (2ZRBTXX__) is a style tee to be used with
Z-Flex rigid liner or when stacking two tees together. Refer to flex ready tee
for use with Z-Flexible liner.
Available in
the following diameters: 3", 4", 5", 6", 7", 8",
9", and 10"
The Stainless
Steel Increaser (2IN_I_X) is used to increase the liner size to accommodate a
range of flue sizes, appliances, and installations.
Available in
the following diameters: 4", 5", 6", 7", 8", and 10”
The
Stainless Steel Reducer (2RD_R_X) is used to decrease the liner size to
accommodate a range of flue sizes, appliances, and installations.
Available in
the following diameters: 2”, 3", 4", 5", 6", 7", and
8"
The Stainless
Steel Top Support (2ZTSXXX__) prevents rain or snow from entering the chimney.
Top support clamps to Z-Flex liner to support the venting system and also holds
the rain cap in place.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Nose Cone Tools
The Nose
Cone (2NCXXX__) is used to snake flexible chimney liner down chimney flue.
Tapered design self-centers liner for smoother installation.
Available in
the following diameters: 3", 4", 5" 5.5", 6", 7",
8", 9", and 10"
Chimney Liner Finder - Gas & Oil
Stainless Steel Aerocowls
The Stainless
Steel Aerocowl (2ARCOWL__) is an aerodynamically designed unit, when fitted to
structurally sound chimneys and flues, completely eliminates downdraft and
thereby prevents troublesome smoke and toxic fumes which otherwise linger in
the home.
Available in
12” and 18” diameters.
The Stainless
Steel Aerocowl Round Base (2ARCORB__) is used to snake rigid chimney liner down
chimney flue. Tapered design self-centers liner for smoother installation.
Available in
the following diameters: 5",
6", 7", 8", and 10"
The Stainless
Steel Aerocowl Universal Base (2ARCOUB) is used to snake rigid chimney liner
down chimney flue. Tapered design self-centers liner for smoother installation.
This base can fit with all the diameters the normal base can fit.
No comments:
Post a Comment